Le migliori offerte per Modulo laser,Doccia a pioggia

Greg Partlow 12/10/2018

I have this rigged up to a thrown together cnc machine with 4 steppers and 4 tb6600 stepper drivers hooked up to an arduino mega running with grbl and now with this 5W laser engraving module. I wish there were instructions or google searches with people who did this more but there are not. so here's some tips. I found if I put the dangly cable where the power is coming in from connected to the ground on the arduino and the + on the ttl/pwn thing on the right part it works, after doing the $32 enable laser mode on the grbl settings. then throw in some g-code generated from inkspace with some laser plugin (which puts the m3 and m5 gcode to turn on and off the laser module) in to g-code sender platform, it works very well. I engraved a bunch of phallic objects that I can't really add as another picture here due to it being inappropriate and just juvenile but, what other test subject matter is there than a few huge richards to laugh at. the after adjusting the focus a little it makes a very small ~0.5mm burn dot. I tried it on some wood planks I had laying around which made my garage smell wonderful from the burning wood.

Modulo di incisione laser da 450 nm e 5W con luce blu con modulazione TTL

US$127.04 US$199.90

13

Commento (1)

Greg Partlow 06/01/2020

works well. I don't understand why the colors are the way they are. I would have thought blue would be cold then green would be good and red would be hot but apparently green is cold and blue is the good temp. other than that it takes a second to install and works well.

Doccetta quadrata in acciaio inossidabile di 6 pollici regolabile a 360° con luce a LED e controllo della temperatura a 3 colori per il bagno

US$23.99 US$28.99

0

Commento (0)

Greg Partlow doingwhat with aluminum, just engravings or cutting?

robhampson 20/08/2018

good quality, perfect for alluminium

6Pz R0.5-3mm HRC45 2 Flauti Fresa Sferica di Azoto Strumento Set della Taglierina Fresatura CNC Rivestito

US$16.19 US$17.65

0

Commento (1)

Glucometro per misuratore di zucchero diabetico per glucometro nel sangue Salute Sistema di cura Nero

US$27.99 US$28.99

D: my question is 11111, if the wrench also can blood monitor? 11111?

Domandata da Whamsplat il 2019-03-12 10:33:36

Greg Partlow I can't imagine that this is a real question. perhaps you are training today?

2019-03-12 04:15:31 Utile (1)

Consegnare

risposta (1)

11 Adattatore Adattatore 7777 Adattatore

US$111.00

D: what is this?

Domandata da Greg Partlow il 2019-03-12 04:14:23

VijayColaco god knows..

2019-03-14 04:44:18 Utile

Consegnare

risposta (1)

Greg Partlow 02/01/2019

the digital display is nice

Modulo Regolatore di Tensione DC-DC LM2596 Step Down Regolabile con Display

US$5.99 US$9.99

0

Commento (0)

Greg Partlow 02/01/2019

this spits out lots of data very fast

Sensore di campo magnetico bussola giroscopica accelerometro di posizione angolare 9DOF integrato a 9 assi MPU9250

US$13.86 US$9.06

0

Commento (0)

Greg Partlow 02/01/2019

not sure what i'm going to use this for yet but it works on the i2c interface

MAX30102 Tester di frequenza dei battiti cardiaci Modulo sensore di frequenza cardiaca Rilevamento dei polsi Test di concentrazione di ossigeno nel sangue

US$3.99 US$11.99

0

Commento (0)

Greg Partlow 24/11/2018

I thought I was going to be in a world of hurt putting this together attempting to translate the translated instructions, but a key highlight with these instructions was little notes telling you what not to do and how to put things correctly to not mess them up. e.g. 'make sure the long side of the capacitor goes in this hole' the resistor either my multi-meter is terrible or the components values are slightly off, either or, there was some minor dependencies in the values the components stated they were. it fired right up though once all soldered in, though I need to watch a video on how to actually use it because just pushing buttons like the guys in videos doesn't work as easily as one would have thought.

Kit originale DIY per oscilloscopio digitale scomponibile DSO-SHELL DSO150 15001K di JYETech con custodia

US$29.99 US$45.99

0

Commento (0)

Greg Partlow 01/11/2018

I tested this connected to an 18v lithium ion battery block with good results. it heated up a screw within 10 seconds. this video shows a demonstration of the unit. https://youtu.be/zk7RPzUCk_E

Macchina di riscaldamento a induzione ZVS Geekcreit® da 1000W 20A con ventola di raffreddamento, PCB tubo in rame 12-36V

US$49.65 US$51.99

1

Commento (0)

Modulo di incisione laser da 450 nm e 5W con luce blu con modulazione TTL

US$127.04 US$199.90

D: Is this laser a circular or square/rectangle beam? Thanks.

Domandata da baxtred il 2018-06-19 04:46:50

Greg Partlow it's not square or completely circular. I'd say it's a cross between a square and rectangle. more of an oval type shape just under 1mm I'd say

2018-10-25 03:36:11 Utile

Consegnare

risposta (1)

Modulo di incisione laser da 450 nm e 5W con luce blu con modulazione TTL

US$127.04 US$199.90

D: Is the focus point adjustable to be less than 1mm?

Domandata da Lorenzo JB Saponetta il 2018-10-12 06:06:55

Greg Partlow it looks just under 1mm though. but it's sort of an oval type shape instead of a circle

2018-10-25 03:34:47 Utile (1)

Consegnare

risposta (2)

Greg Partlow one thing to note, I had this connected to the original power supply that came with the unit. it did not engrave anodized aluminum this way. I connected the board up to the same power supply that drives the steppers which is a more consistent output and now I can engrave on to anodized aluminum at 300mm/m feed. here's a picture of the laser etching into an anodized aluminum business card https://i.imgur.com/cqiM2qj.jpg

Greg Partlow 12/10/2018

I have this rigged up to a thrown together cnc machine with 4 steppers and 4 tb6600 stepper drivers hooked up to an arduino mega running with grbl and now with this 5W laser engraving module. I wish there were instructions or google searches with people who did this more but there are not. so here's some tips. I found if I put the dangly cable where the power is coming in from connected to the ground on the arduino and the + on the ttl/pwn thing on the right part it works, after doing the $32 enable laser mode on the grbl settings. then throw in some g-code generated from inkspace with some laser plugin (which puts the m3 and m5 gcode to turn on and off the laser module) in to g-code sender platform, it works very well. I engraved a bunch of phallic objects that I can't really add as another picture here due to it being inappropriate and just juvenile but, what other test subject matter is there than a few huge richards to laugh at. the after adjusting the focus a little it makes a very small ~0.5mm burn dot. I tried it on some wood planks I had laying around which made my garage smell wonderful from the burning wood.

Modulo di incisione laser da 450 nm e 5W con luce blu con modulazione TTL

US$127.04 US$199.90

13

Commento (1)

Greg Partlow 08/10/2018

every part was in a bag. it wasn't protected very well, though it finally came after a month on the slowest boat to navigate the world it came without injury. I need to stop buying these though. I have too many now.