DuaneMHunt1976
D: how does it attach to the surface, a vice holds but you need it to be attached so it holds steady!
Domandata da DuaneMHunt1976 il 2020-07-26 02:06:04
D: does it contain 10ohm resistor???
Domandata da Kumar Pallav il 2018-04-07 11:43:22
DuaneMHunt1976 0ohm,2.2ohm, 4.7ohm, 5.6ohm, 7.5ohm, 8.2ohm, 10ohm, 15ohm, 22ohm, 27ohm, 33ohm, 39ohm, 47ohm, 56ohm, 68ohm, 75ohm, 82ohm, 100ohm, 120ohm, 150ohm, 180ohm, 220ohm, 270ohm, 330ohm, 390ohm, 470ohm, 510ohm, 680ohm, 820ohm, 1Kohm, 1.5Kohm, 2.2Kohm, 3.3Kohm, 3.9Kohm, 4.7Kohm, 5.6Kohm, 6.8Kohm, 7.5Kohm, 8.2Kohm, 10Kohm, 15Kohm, 22Kohm, 33Kohm, 39Kohm, 47Kohm, 56Kohm, 68Kohm, 75Kohm, 82Kohm, 100Kohm, 150Kohm, 180Kohm, 220Kohm, 330Kohm, 470Kohm, 560Kohm, 680Kohm, 1Mohm, 1.5Mohm, 2Mohm, 3.3Mohm, 4.7Mohm, 5.6Mohm, 10MohmN THE LIST IT SAYS 10 Ohms!!
2020-06-12 01:49:59 Utile (0)
D: Hi! For these capacitors what is the name of manufacturer? Are these X7R ? Thnx for answer. Sinisa.
Domandata da sinisa051 il 2020-03-08 06:56:50
DuaneMHunt1976 Inmy time of using SMD Cap or Res i have never seen a maker, it does the job and thats normally all one can ask from it
2020-06-12 01:48:16 Utile (0)
D: Which values content? How many each?
Domandata da Juan Pablo Moriatis il 2019-09-11 07:32:44
DuaneMHunt1976 MaybeRead the ADVERT! it does say what values are in the PACK and how many of EACH! and on that NOTE, i wouldnt know in Person as It DID not Turn up! Guess too CHEAP to be TRUE
2020-05-11 03:15:50 Utile (1)D: Can I use this connector to power my TS100 soldering iron ?
Domandata da MarcAntoine il 2019-04-18 04:35:22
DuaneMHunt1976 wellthis is just the connector, so if you have a Transformer (RIGHT AMPS and VOLTS, and CABLE that can handle it) But if your asking if this is RIGHT for a SET Soldering Iron, im a bit scared that you may not know what you are doing.
2020-05-11 03:14:36 Utile (0)D: Contiene resistencias de 220 ohms y 560 ohms?
Domandata da vanyAranda il 2019-06-29 01:27:49
DuaneMHunt1976 No sabría, el artículo nunca apareció.
2020-05-11 03:11:33 Utile (0)Ti invitiamo sinceramente a iscriverti all'e-mail di risposta all'invito!
Se ti iscrivi, ti inviteremo via e-mail a rispondere alle domande che le persone hanno sui prodotti. Iscrivendoti] guadagnerai anche il "Badge utile "! Puoi annullare l'iscrizione in qualsiasi momento nella pagina delle impostazioni sulla privacy.
Aiuta gli altri e sii più felice!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
Nelly Using Steps: 1. Clean the table. 2. The vise is placed in table, firmly press the base of wrench and control the handle suck table. 3. The workpiece clamping on the forceps, then can be processed operation.
2020-08-06 01:35:42 Utile (0)