gugi9000
D: Can i use this to get video from any analog quad camera? Just connect to dji goggles and thats it?
Domandata da BG163812451 il 2021-10-31 04:03:39
gugi9000 You need to get an analog receiver as well. This is just the adapter part.
2021-10-31 05:58:48 Utile (0)D: what is the maximum power output?
Domandata da cwchapma il 2021-09-04 07:29:34
gugi9000 250mW
2021-09-26 03:38:08 Utile (0)
gugi9000 The XT30 is to ease the load on the internet batteries of your transmitter.
2021-09-26 03:35:29 Utile (0)D: Does this work with radiomaster tx12?
Domandata da BG163812451 il 2021-09-23 07:26:56
gugi9000 Yes. This is unrelated the the transmitter to receiver. This is analog video only.
2021-09-26 03:34:51 Utile (0)
gugi9000 Yes and no. The VTX transmits analog signal on 5.8 Ghz, but the camera also records 1080p to an SD-card plugged into the quad.
2021-08-09 04:37:30 Utile (2)D: autonomie???
Domandata da alpatch2 il 2021-01-09 03:33:26
gugi9000 No
2021-08-03 01:51:04 Utile (0)D: Hi guys, will it connect with TBS UNIFY PRO 5G8 HV RACE?
Domandata da Paskraidysim il 2021-06-02 07:45:44
gugi9000 Yes.
2021-08-03 01:42:07 Utile (0)
gugi9000 No. It’s has a 5.8 GHz receiver for analog FPV drones.
2021-07-31 09:56:59 Utile (0)
gugi9000 No OSD or anything? Sounds like your device is broken. Contact support.
2021-07-17 02:15:58 Utile (0)D: the stack specification says input: 4s and the ESC says input: 2-5s. so can I run 5s on this or no?
Domandata da yamesve il 2021-07-16 09:56:06
gugi9000 No. That is burst current. You might fry the FC (or the ESC) if you do so.
2021-07-17 02:14:15 Utile (1)D: can these take normal props? like gemfan for example?
Domandata da BG561054346 il 2021-06-20 11:32:56
gugi9000 This is for like 3 or 4 inch props with a 1.5 mm center hole and two screws (so, I guess: no)
2021-06-20 01:14:29 Utile (0)D: What are the motor and shaft dimensions?
Domandata da JayGeeBSE il 2021-05-22 09:13:28
gugi9000 1.5 mm
2021-05-23 06:13:34 Utile (1)D: Is it High Voltage (4,35V) batteries? Or max voltage is 4,2V?
Domandata da BG403217573 il 2021-05-23 04:59:31
gugi9000 It’s HV 4.35V. Says right there in the description ;-)
2021-05-23 06:12:56 Utile (2)
gugi9000 Does your printer otherwise match the picture of the Ender 3Xs Pro on this page?
2021-04-17 11:41:45 Utile (0)
gugi9000 It does.
2021-04-15 12:20:33 Utile (0)
gugi9000 No.
2021-04-13 10:20:04 Utile (0)
Ti invitiamo sinceramente a iscriverti all'e-mail di risposta all'invito!
Se ti iscrivi, ti inviteremo via e-mail a rispondere alle domande che le persone hanno sui prodotti. Iscrivendoti] guadagnerai anche il "Badge utile "! Puoi annullare l'iscrizione in qualsiasi momento nella pagina delle impostazioni sulla privacy.
Aiuta gli altri e sii più felice!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
gugi9000 18 watts. See the description 😉
2021-11-13 12:21:03 Utile (0)