Le migliori offerte per Wire Plier,Stazione di saldatura

TY Modello 3-2 370 millimetri Apertura alare balsa Laser legno tagliato RC RTF

D: What frequency does the receiver use? I have a couple of multi protocol transmitters modules for my Taranis. I prefer flying with a full size transmitter if possible.

Domandata da FlingingChopstick il 2017-11-13 09:45:04

cilia This receiver uses electromagnetic rudder,it is not compatible with other transmitter.

2017-12-12 08:55:18 Utile (1)

Consegnare

risposta (2)

SN-01BM AWG28-20 Terminale Cavo Spellacavi per Dupont PH2.0 XH2.54 KF2510 JST

US$23.09 US$23.99

D: Will this crimp JR servo connectors?

Domandata da FlingingChopstick il 2018-11-27 04:58:14

Barry NO, NO, NO, these are NOT suitable for making servo plugs. The jaws are too narrow. These are only 4mm wide. To make u servo leads the jaws need to be 6.4mm wide. No NOT buy this product.

2020-01-15 03:57:53 Utile (3)

Consegnare

risposta (7)

FlingingChopstick 29/05/2018

This is more solidly built than I expected it to be. Of course I just received it and it hasn’t had time to be tested for durability. The base is more solid and heavier than expected too.

YP-001 Base metallica Universale per Stazione di Saldatura con 4 Bracci Flessibili, Fixture PCB e Aiuti Quattro Mani

US$45.03 US$46.99

0

Commento (0)

FlingingChopstick 23/02/2018

I first bought a Tevo Tarantula because, being new to 3D printing, I wanted to learn each part and function. It was not a great experience. It is not a well designed printer either, but the price was right. So, then I paid basically double the price the CR-10. It's a great machine and I've made many successful prints. However, there was one critical problem, which I found after searching 3D forums is very, very common with the CR-10. The glass for the heat bed is poor quality. There is a dip in the center of the glass. Meaning, it's not level, thus it's impossible to level your bed! Doing small prints works OK, but larger prints fail constantly. I replaced the glass with a high quality glass build plate made specifically for 3D printing,($50+) and now it works like a champ. So be ready to replace the glass when you buy the CR-10. Unless you are only printing small things. Also, DON"T use tape. For PLA heat up your bed to 60C and put some glue stick on your print area. It will stick every time. Also, If you are looking to print things like PETG, you will need to replace the nozzle and hot end. It won't get to the minimum 230C required. It seems to top out at about 220-225C. But, I still think it was worth the money spent.

Creality 3D® CR-10 DIY 3D Stampante Kit 300*300*400mm Dimensione di Stampa 1.75mm 0.4mm Ugello

US$473.54 US$444.39

0

Commento (0)

FlingingChopstick 20/02/2018

I had a log-jam with my printer. I was printing PETG filament and I walked away for about 30 minutes after it was an hour in to a 4 hour print. When I came back, the hot end wasn't moving anymore and a big pile of plastic surrounded the nozzle. I cleaned it and then tried to print PETG again at 235C. The hot end would not even get up to 230C, the low temp recommended by the filament maker. So I thought I had ruined it, so I bought this. Well, I have the same problems. It just fluctuates between 226-228C and won't get any hotter. Perhaps this is the CR10 original problem, but this didn't fix my problem. It is working great for PLA... but that's not all I want to print. I'm now looking for nozzle and hot end that will reach the temps I need.

Kit Parti per Stampante 3D 0.4mm Ugello Estrusore con Ventilatore di Raffreddamento per Creality CR-10

US$45.87 US$68.81

0

Commento (1)

FlingingChopstick I don't see the charge plate and charger in the picture. If you can't put those two items in, then it's as worthless as the 2 cases DJI gives you with the fly more combo.

G2loq 19/07/2017

I received the bag I expected, I mean the one with the transmitter trail. I also confirmed that there is no 2 foam set with this handbag... as we can presume by seing the different pictures. For me it was ok, but I hope that in the future, Banggood will propose 2 options and not only one as today ! Otherwise, it will be lottery ! By the way, I also have the hard casing version (Realacc Waterproof Hardshell Backpack Case Bag RC - very heavy compare to this one), and I really prefer this one. I have 6 batteries (I know it is a lot hehe) and I was able to install all of them. There is only 3 cavities for the battery but you will be able to find more. I also really prefer the "not too deep cavity" for the sparl, as it is very easy to pull it, still compare to the Realacc Waterproof version).