BG203725422
D: will this heater work with an afterburner controller
Domandata da BG501141750 il 2023-11-28 09:15:56
BG203725422 I believe that the Bluetooth controller and its mainboard are shown as not compatible with the afterburner controller. If you refer to the afterburner website they list which controllers are compatible and which are not compatible
2023-12-04 02:20:01 Utile (0)D: compatible pour alfawise i30 pro? et droite ou gauche ? Merci
Domandata da noto 60 il 2020-11-14 07:25:25
BG203725422 I do not know
2023-11-26 04:19:32 Utile (0)
BG203725422 I use file clips
2023-11-26 04:19:15 Utile (0)
BG203725422 No
2023-11-26 04:18:52 Utile (0)
D: Is this "Carborundum" coated glass?
Domandata da RENOxDECEPTION il 2021-04-26 05:29:34
BG203725422 Not sure about the carborundum glass, but I have 4 of these glass beds and use the un-coated side with a bed adhesive, gives very nice smooth finish to the parts. Let the glass bed fully cool down or I even put it my freezer before removing the prints, mostly they just pop off and because the glass provides a tough surface you don’t get damage if z-height offset is a little off.
2022-06-14 01:25:16 Utile (0)
BG203725422 Newer Creality printers come with press fit gears on the extruder stepper motors and are a pain to remove, but you can achieve this and the original motor will work fine. If you want a direct drive unit this should work but mounts will need to be purchased or printed to convert.
2022-06-14 01:21:14 Utile (0)D: Will this allow for printing with flexible filament?
Domandata da bmack il 2020-09-30 10:58:14
BG203725422 You can print tpu easier with dual gear extruder, but you must adjust z-height adjustment and slow print speed to get any success, don’t go too soft as jams and retraction become serious issues
2022-06-14 01:17:08 Utile (0)
BG203725422 Yes, you may need new stepper motor as Creality push fit extruder gears and you also need to adjust e-step values
2022-05-30 11:58:44 Utile (0)D: Does it fit Ender-3 V2? Thanks
Domandata da BG651411359 il 2020-12-26 02:39:57
BG203725422 Yes, but remember you may need a new stepper motor as Creality use push fit gears and adjust your e-step values
2022-05-30 11:57:46 Utile (0)
BG203725422 I don’t know sorry
2022-05-30 11:56:53 Utile (0)
Ti invitiamo sinceramente a iscriverti all'e-mail di risposta all'invito!
Se ti iscrivi, ti inviteremo via e-mail a rispondere alle domande che le persone hanno sui prodotti. Iscrivendoti] guadagnerai anche il "Badge utile "! Puoi annullare l'iscrizione in qualsiasi momento nella pagina delle impostazioni sulla privacy.
Aiuta gli altri e sii più felice!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
