Una parte della recensione è stata tradotta automaticamente.
I bought the FlySky FS-i6 for all my 10 drones. It supported the old AFHDS protocol for using mini RX receiver (DasMikro Ultra Miniature) and with AFHDS 2A I'm using all my RX receiver FS-iA6B. It come with USB cable for flashing or training on PC. The transmitter ist for beginner and for advanced aviators. With iBUS protocol you can use all the 4 buttons and two variable buttons on your quadcopter. Low cost and very, very good.
Fonctionne très bien, je l'utilise en I-bus sur une SP F3 racing de chez Bangood. A savoir : bien que vendues ensemble, il faut binder le récepteur avec la radio!
Great Transmitter! Great Price! It was a bit of a challenge, as a newbie, to get all 10 channels to be enabled with the FS-A8S receiver. No firmware update is needed! I used two 16 channel converter modules, S2PW's, (each only has 8 outputs configurable for channels 1-8 (no red light) or 9-16 (red light active). The converter modules are setup, factory stock, to be channels 1-8. To enable channels 9-16 you need to press the button and hold it in while powering on those modules, then release. This only needs to be done once and they save their settings. The FS-A8S needs to be connected to the i.BUS input of the S2PW module configured for channels 9-16 (red light) when using more than 8 channels. The module, with the red lights output needs to be connected to the input of the second S2PW module configured as Channels 1-8 (no red light). At first, I had the A8S connected to the channel 1-8 module (no red light) and it did not allow channels 9-10 to get through to the second module. I then connected the A8S to the channel 9-16 module (red light) and everything works as expected with the 10 Channels of this radio. I included a Photo with how I set this up, the yellow wire between the two S2PW modules is the i.BUS signal. Red and black wires are power and ground wires. The transmitter "RX Mode" settings need to be set to output PPM on i.BUS. You also need to turn on all the AUX Switches. Save all settings and go into the "Display" mode of the transmitter, press UP/DOWN buttons to view channels 8-10. There is also a much more detailed manual on the manufacture website product page, there is no need to update the firmware to enable 10 channels and it may actually downgrade your radio to older firmware.
1. cheap; 2. popular; 3. w/ i-bus included; 4.up-gradable (antenna/battery/firmware); 5. responsive; 6. even skins are available for this one!... It deserves to be choosen.
Qualità accettabile, non sembra giocattolo, ma per il prezzo, adatto a coloro che hanno iniziato nella RC, ci sono voluti meno di quanto detto all'inizio, fino a 15 giorni, spero di poterlo usare presto, Ma con pratiche sufficienti! 😊
ürün açıklamasında yazdığı gibi geldi. bu mesajı Türk kullanıcılar için yazıyorum. Gönül rahatlığı ile alabilirsiniz.
Ricevuto nel tempo e nella forma, la qualità dei materiali è buona, non direi eccellente ma per il prezzo è più che sufficiente, ancora non lo assaggio davvero, sto aspettando un altro articolo da provare, ma è apprezzato più che bene, grazie bangood
Perfetto! pacco un po 'danneggiato, ma è i servizi postali che la sua attenzione se non funziona perfettamente che cosa è un peccato che manca un manuale per il ricevitore fs x6b con ma dovrà essere trovato su internet, Di conseguenza, non ha potuto provare il ricevitore ancora. Mi raccomando questo è un ottimo set per questo lanciato nel fpv e capire come collegare un vero ricevitore che sembra davvero più potente del fsa8s.
Molto buono 2,4 GHz 6-10 ch trasmettitore per i miei aerei. Con i sensori di altitudine e di tensione si potrebbe monitorare quanto è alto l'aereo e la capacità della batteria. E se si aggiorna il software, si potrebbe monitorare RSSI.
Caratteristica desiderata a un prezzo ragionevole