Le migliori offerte per WIFI Tuya Smart Door serratura,stampante 3d,Scheda amplificatore digitale - Banggood Italy Shopping online

NightOne

i miei contenuti: Tutti i messaggi; Recensioni; Commenti; risposta; Domande

Tutti i messaggi

NightOne 03/09/2021

Very fast delivery, very happy with device, waterproof and well made, took me about 10 min to replace old keypad with new. The only negitive that I have found is that you can only have a 4 digit public code. Not a big issue for me because I use card and pin code. Also pairing with Tuya app is very easy to set up. Would definelty recommend.

WIFI Tuya Smart Door serratura Sistema di controllo accessi per porte Tastiera standalone Controller di accesso per porte con scheda 125KHZ

US$27.46 US$39.87

0

Commento (0)

NightOne 03/09/2021

Very well made and great fun to put together, I would recommend watching youtube videos on the set by set build process as it helps a lot. One very important issue when building is to make sure you push the PTFE tube all the way into the hot end...it has to go in about 5 cm...I made the mistake of not pushing it in far enough as I felt resistance and didnt want to force it....this caused the hot end to jam and I had to take hot end part to clean the jam (youtube "how to" again). I have on negitive about the quality of the filament extruder, it only has a single drive and it skips like crazy right from the start... its also made out of plastic and you need to be really carefull screwing it down otherwise you will crack the plastic. I tried for 3 days to get it to work properly and eventually gave up and replaced it with dual drive extruder from old printer. One huge plus is the hot end and the cooling...the dual fan cooling is fantastic, but does cause one issue....when you upgrade the firmware yourself to the latest Marlin you need to tweak the thermal runaway settings....the fan is so effective that when it turns on after the first layer it triggers a thermal runaway error (hot end temp drops 11 degrees in two seconds) and the print stops..... I would also recommend upgrading the stepper drivers to TMC 2208s as they are much quieter and improve the print quality greatly.. I am extremely happy with this printer.

HOMERS/TEVO® Tarantola Pro Kit stampante 3D con dimensioni di stampa 235x235x250 mm MKS Scheda madre GenL 0,4 mm Supporto ugello vulcano Filamento 1,75 mm

US$264.49 US$434.76

0

Commento (0)

TPA3116 2.1 DC 12V-24V 50W + 50W + 100W HIFI Scheda amplificatore audio digitale

US$33.48 US$34.99

D: in this board from where can i extract 5 volts ?

Domandata da Nehal Rai il 2019-01-16 01:58:13

NightOne Turn the board over....under the board you will see Vout 5v output...120mA

2019-02-06 01:06:27 Utile (1)

Consegnare

risposta (3)

SL-LC 01 Super Mini LED WIFI Smart Controller RGB per striscia LED RGB DC 5-28V

US$18.47 US$19.99

D: can i connect this to a pc?

Domandata da IMohd il 2019-01-01 09:13:54

NightOne You can use node-red to control this from a PC.....Just search for node-red-contrib-magichome-controller on flows.nodered.org

2019-01-08 02:06:53 Utile

Consegnare

risposta (1)

NightOne 19/06/2018

Installed in less then 5 min on garage door.... very easy to install...both remotes where programed so I didnt have to "teach" the controller.... there was no jumper included on the pins...so had to use a old jumper bridge from computer... Instructions on banggood say that momentary is idle (jumper)....which I assume means no jumper but thats was not true of mine...I had to bridge jumpers 1-2 to set it to momentary...meaning hold button A to switch relay on....let go button A to switch relay off. Works great.

DC12V 433MHz Relay 1CH Wireless RF remoto Trasmettitore di comando per luce

US$19.54 US$20.99

1

Commento (0)