Wes
D: Should the fan turn on when the external module is powered or will it only power on when it get hot?
Domandata da Mcrgaming il 2021-11-08 03:32:47
D: what size is the prop hub shaft? 5mm? 6mm?
Domandata da Andy0679 il 2021-08-08 05:43:55
Wes The PNP kit I received included SunnySky X2216-7 and 1400KV with 5mm shaft
2021-08-08 06:35:46 Utile (2)D: What voltage are the PNP servos rated for?
Domandata da WillF il 2021-06-14 05:27:21
Wes The spare part is available for AR Wing Pro and the spec sheet says 4.8 to 6V DC.
2021-06-14 06:21:08 Utile (1)D: Can this be used with the Flysky iBUS system? Specifically, the IA6B reciever?
Domandata da Scrim il 2021-04-25 07:45:51
Wes The manual for F405-Wing shows use UART2-RX RX2 pad for IBUS, PPM etc., instead of Sbs pad which is for SBUS.
2021-04-25 09:07:33 Utile (0)D: Can it be precisely positioned in its 270 degree sweep or does it just spin endlessly CW/CCW?
Domandata da humanseeing il 2021-02-24 02:12:45
Wes I tested it on servo tester and it sweeped 180 deg. like normal proportional servo. Instructions say to increase pulse width to obtain 270 degrees. I haven't tried that yet, but I expect it will work as advertised.
2021-02-24 04:18:55 Utile (1)D: hello, does this camera have infrared system? and work in dark? thanks
Domandata da BG203443161 il 2021-02-06 12:37:36
Wes It says .01 minimum illumination at 1.2F so you need something like .0001 or .00001 like night eagle II or cat 2 starlight for night. The night eagle II is black and white only but it is the best one for night vision.
2021-02-06 01:29:03 Utile (1)D: hi what are the sizes of the battery width, height, length
Domandata da JGsnr il 2020-11-13 03:17:02
Wes I get about 2 and seven eighths
2020-11-13 04:07:48 Utile (0)
D: how do i set rth failsafe for flysky ppm reciever??
Domandata da 360noscopy il 2020-08-11 08:38:59
Wes Check what channel you assigned in the Owl's setup menu to be RTH first. Once you setup the flight controller and got the mode and sub-mode switches set you can verify in your OSD which switch or switch combination activates RTH. Then you can go into System -> RX Setup -> Failsafe and set the mode switch channel and sub-mode switch channel (if you setup a sub-mode switch) to the values that select the proper switch position(s). For example on mine I have channel 5 mode switch with manual, stabilized, and sub-mode, then I have channel 6 set to althold, circle, rth. So if -100% is where sub-mode is on channel 5, and -100% is where RTH is on channel 6, then I can set just those channels to -100% and then press the cancel button on my FlySky TX to save those settings. To verify I can power up the TX and plane and see it's all working in the OSD, then turn off the TX and if it's working the plane (Owl flight controller) will go into RTH. Only change the channels which activate RTH, don't for example set the throttle to -100% because the RTH will control that. SAFETY NOTE: You should always remove your propeller when testing in case it powers up by some error to avoid serious injury.
2020-08-11 09:36:33 Utile (1)D: Does it come with ZOHD Kopilot?
Domandata da BG231341021 il 2020-07-24 12:09:11
Wes Order the FPV Version to get the ZOHD Kopilot Lite and VC400 All in one Camera included. You will have everything you need to fly FPV, but you must provide your own battery, rc receiver, and rc transmitter, as well as some kind of FPV goggles or monitor.
2020-07-24 12:31:37 Utile (2)D: Do you have the channel list for the vtx and Rx?
Domandata da folatoye il 2019-01-10 11:55:41
Wes The800mW TX is listed in the description as frequency. The Receiver Channels: CH0 0.910G CH1 0.980G CH2 1.010G CH3 1.040G CH4 1.080G CH5 1.120G CH6 1.160G CH7 1.200G CH8 1.240G CH9 1.280G CH10 1.320G CH11 1.360G
2020-07-22 07:51:37 Utile (0)
D: will it bind to an FRSKY QX7?or i have to install anrw receiver for FrSky?
Domandata da alanhabri il 2019-06-19 09:50:30
Wes Youneed a multiprotocol module for example I use KN --> WlToys protocol for this model on my Jumper T8SG V2 Advanced radio.
2020-07-02 09:07:52 Utile (0)
Wes Youselect LH or RH to match your VTX antenna (RHCP TX to RHCP RX or LHCP TX to LHCP RX). Each port on the screen is an independant RX so you can put it in either connector. The best way to use this "diversity receiver" setup is a directional "beam" type in one, and an omni-directional antenna in the other. The beam type must be pointed at your craft TX antenna, and the omni-directional will work in basically all directions (all antennas do have some small null areas to keep in mind).
2020-07-02 09:03:09 Utile (0)Ti invitiamo sinceramente a iscriverti all'e-mail di risposta all'invito!
Se ti iscrivi, ti inviteremo via e-mail a rispondere alle domande che le persone hanno sui prodotti. Iscrivendoti] guadagnerai anche il "Badge utile "! Puoi annullare l'iscrizione in qualsiasi momento nella pagina delle impostazioni sulla privacy.
Aiuta gli altri e sii più felice!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
Wes It's supposed to turn on automatically at 250mW power setting.
2021-11-08 06:10:22 Utile (1)