BG445364424
i miei contenuti
Tutti i messaggi
Recensioni
Commenti
risposta
Domande

Tutti i messaggi

BG445364424 13/08/2023
Arrived on time, partially charged. They were easy to fully charge and work as expected in a couple of torches and hand-held lasers. Have not taken the time to test the mAh rating.
2PCS 3.7V 5200mAh Batteria ricaricabile protetta Li-ion 18650 per controller radio RadioMaster Pocket Radio Transmitter
US$10.49 US$9.99
0
raccomandazioni
Commento (0)
BG445364424 23/08/2020
Great little project for someone with a little experience since there were no directions. Works well and it just needs a good power supply. It was interesting that the LED frequency display shuts off after a few seconds, but it keeps the last tuned frequency when turned on and off with the switch. Would like to see a slightly better connection for the whip antenna for FM.
TEA5767 DC 4.5V-5.5V Mini FM digitale fai-da-te Radio 87MHZ-108MHZ 2W 8ohm Speaker Electronics Kit
US$13.82 US$23.92
1
raccomandazioni
Commento (0)
BG445364424 24/09/2020
This DIY FM radio using the TDA5807 and LCD display has a much cleaner sound than the designs using the TEA5767. It does have digital controls for the volume where the lowest level, 0, is still audible. Like other FM kits, it only stops when it scans and detects a strong signal, so weaker stations may be missed. Increasing the volume allows the lights across the top to light up, and if sufficiently loud, the centre ones will start to change colour (curious when the installed LEDs are just two pins). Some written directions might have been helpful. To help secure the antenna, which was threaded, I used a M2x8mm bolt. The three lengths of bolts was a little confusing about where they should be used. In some places, I actually replaced the metal bolts with M3 x 12 mm nylon bolts. A headphone jack might be a nice addition.
Geekcreit® DIY Radio Parti del kit elettronico 51 Macchina audio digitale FM a chip singolo
US$22.99 US$23.99
8
raccomandazioni
Commento (1)
BG445364424 29/09/2020
Seems to work as expected. The knob to adjust the voltage is a little hard to turn, and getting the voltage set to exactly 5.0, 6.0, etc, took a little patience. It was used to power a small kit radio and did not seem to affect the radio signals. It came with an adapter to convert the European plug to the local style plugs. It has only been tested for low power loads, so cannot comment on how much current it can produce.
KJS-1509 3-12V 5A Adattatore di alimentazione Adattatore di tensione regolabile LED Display Alimentatore switching
US$18.47 US$23.99
0
raccomandazioni
Commento (0)
Kit stampante 3D aggiornata Creality 3D® Ender-3 V2 dimensioni di stampa 220x220x250mm Scheda madre a 32 bit ultra silenziosa TMC2208/ Piattaforma in vetro di carborundum/ Alimentatore Mean Well/ Nuovo schermo a colori 4,3 pollici
US$378.35 US$329.00

D: Can I print from PETG on this printer?

Domandata da BG114738323 il 2020-09-22 02:16:51

BG445364424 TheEnder 3 v2 is able to print with PLA, ABS, PETG and TPU. At this point I have only used PLA, but I hope to print with some PETG when I get some filament.

2020-09-25 04:40:18 Utile (0)
Consegnare
risposta (4)
BG445364424 24/09/2020
Gift for a friend who like to work with Arduino, so hopefully he can work out how to control this and make it into a radio project.
TEA5767 FM Modulo Radio Stereo 76-108MHz per Arduino con Antenna
US$15.00 US$15.99
0
raccomandazioni
Commento (0)
BG445364424 24/09/2020
Batteries arrived on time, come in a nice little plastic case, and seem to work well.
4 pezzi SORBO 1.5V 1200mAh Batteria ricaricabile AA Li-po con ricarica rapida in 1 ora tramite USB
US$25.29 US$29.99
0
raccomandazioni
Commento (0)
BG445364424 24/09/2020
One USB A to four USB micro - very useful.
Cavo di ricarica micro USB ZNTER per batteria ricaricabile USB
US$8.07 US$8.99
0
raccomandazioni
Commento (0)
BG445364424 24/09/2020
Love this little soap foam dispenser. Just make sure you use foaming soap refill. The smiling face that flashes for ten seconds is a great reminder to rub your hands together longer and it helps light up the sink at night.
[Versione ottimizzazione] Xiaowei 250ML Smart Sensor Induzione automatica di schiuma liquida Sapone Dispenser Sensore a infrarossi Attrezzatura per la schiuma
US$26.57 US$27.00
0
raccomandazioni
Commento (0)
BG445364424 24/09/2020
This project went together rather easily (no directions, just pictures on the website), and seems to work well after some initial testing.
Fai da te AC 220V a DC 1.25V-12V LM317 Kit modulo di alimentazione regolabile con alloggiamento
US$13.79 US$15.99
0
raccomandazioni
Commento (0)
BG445364424 24/09/2020
Putting in all of the LEDs took some time, but the rest of the assembly went very smoothly and quickly. Now I just need to work on getting the settings worked out. After about 15 seconds the display scrolls to show other information such as the temperature, date and alarm setting.
Geekcreit® quarta generazione fai da te EC1838B DS3231 controllo della luce rotazione LED kit orologio elettronico sveglia musicale con custodia
US$16.79 US$18.99
0
raccomandazioni
Commento (0)
BG445364424 16/09/2020
What arrived was a different brand but marked 600 mAh and charged and ready to use. Seem to do the job after an initial check.
Batteria al litio-polimero ricaricabile USB ZNTER S19 9V 600mAh 9V
US$18.47 US$19.99
0
raccomandazioni
Commento (0)
BG445364424 07/09/2020
Works well for surface mount components when you only need small amounts of solder.
0,4 mm 63/37 piombo di stagno Saldare Nucleo di colofonia per filo saldatura Tubo per bobine di flusso al 2%
US$10.38 US$10.99
0
raccomandazioni
Commento (0)
BG445364424 07/09/2020
It took some effort to do the initial levelling of the print bed, but otherwise it seems to print very well and is quiet when printing (other than the fan). Only tried PLA at this point.
Kit stampante 3D aggiornata Creality 3D® Ender-3 V2 dimensioni di stampa 220x220x250mm Scheda madre a 32 bit ultra silenziosa TMC2208/ Piattaforma in vetro di carborundum/ Alimentatore Mean Well/ Nuovo schermo a colori 4,3 pollici
US$378.35 US$329.00
0
raccomandazioni
Commento (0)
BG445364424 07/09/2020
Other than one tiny surface mount component, this is a great little FM radio and pretty easy to solder together. Not sure why, but the one I ordered did not have a battery, but I bought version #1 and there are three other versions that can be purchased.
Kit elettronico fai-da-te ricaricabile FM stereo digitale Radio parti fai-da-te
US$17.31 US$12.99
0
raccomandazioni
Commento (0)
BG445364424 07/09/2020
Amazing reception for a small hand-held radio. Shows the temperature, lets you select rechargeable or non-rechargeable batteries. Easy to program. Just wish I had an English version of the user manual (but it was relatively easy to find online).
TECSUN PL360 Portable AM ​​FM a onde corte PLL DSP ETM SW MW LW Pocket Digital Radio ricevitore
US$78.54 US$76.00
0
raccomandazioni
Commento (0)
BG445364424 25/08/2020
This was a challenging radio to assemble and tune, but was functional in the end. The fit of the molded plastic parts could be improved.
DIY Portabile AM FM Radio Kit 76-108MHZ 525-1605KHZ Adatta per Electronic Insegnamento e Apprendimento Elettronico
US$6.99 US$9.99
0
raccomandazioni
Commento (0)
BG445364424 25/08/2020
Package arrived on time, but I haven't had time to use the product yet.
Pasta saldante KSS S800 10CC per dispensare su fili SMD Bga
US$13.91 US$15.99
0
raccomandazioni
Commento (0)
BG445364424 23/08/2020
Very challenging to assemble without instructions. Still not sure if the tuning mechanism for the display is assembled correctly and if the filter components (3-pin and 2-pin) are installed correctly on the circuit board. Currently it picks up some FM stations and only one AM station which is unusual for this area. Shortwave broadcasts are limited in this area and I don't have an external antenna to assist with SW reception. One really great thing with this radio is the connection to the batteries because the spring terminals mount directly and securely to the circuit board. Unfortunately, the battery compartment seems to open at the wrong end. It is nice to have a headphone output and input for external power. The radio seems to have potential but mine still has lots of issues.
DIY EDT-2902 Multiband Radio Kit Kit di formazione sulla produzione elettronica
US$14.99 US$20.99
0
raccomandazioni
Commento (0)
BG445364424 23/08/2020
Nice little AM radio kit with reasonable reception. Probably just needs to be tuned better to improve reception. No earphone connector, so just a small speaker for sound. Curious location for batteries next to the speaker so they are attracted to
Kit Fai da Te Elettronico Sette 07:00 Radio di Apprendimento Elettronico
US$7.55 US$9.06
0
raccomandazioni
Commento (0)

Sei l'esperto, puoi aiutare?

Ti invitiamo sinceramente a iscriverti all'e-mail di risposta all'invito!

Se ti iscrivi, ti inviteremo via e-mail a rispondere alle domande che le persone hanno sui prodotti. Iscrivendoti] guadagnerai anche il "Badge utile "! Puoi annullare l'iscrizione in qualsiasi momento nella pagina delle impostazioni sulla privacy.

Aiuta gli altri e sii più felice!

  • sottoscrivi

Informazioni sui badge

I badge sono collegati alla community e gli utenti guadagnano badge creando contenuti di qualità, completando missioni o partecipando ad attività speciali. Le persone specifiche avranno anche il proprio badge esclusivo.
Badge CEO

il badge ceo è di proprietà solo del boss di banggood.

I badge che puoi guadagnare arriveranno presto
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe