CrispyDuck
i miei contenuti
Tutti i messaggi
Recensioni
Commenti
risposta
Domande

Tutti i messaggi

Piastra passiva in alluminio da 2,5 mm per asse Z Creality 3D® per CR-10S Pro Stampante 3D
US$9.23 US$9.99

D: Does this fit the original Creality CR-10 for a Z-axis upgrade?

Domandata da CrispyDuck il 2021-03-22 05:46:54

FJavierGavira Siempre que puedas multiplicar el uso de un driver de Z con sincronización o poniendo 2 motores y usillos podrás aplicar doble eje Z. Con esta chapa montas el segundo Z en el perfil de guía del carro hotem

2022-04-27 11:08:38 Utile (0)
Consegnare
risposta (3)
CrispyDuck 20/03/2018
This is excellent once you get it working. It is very similar to the NeoPixel rings and work in the same way. . Unfortunately noone has so far put any instructions on her as to how to get it working, so they are now below... This works with the NeoPixel Example sketch "RGBWstrandtest" if you connect it up correctly. Connect the LED Ring "GND" to the GND on the Arduino as well as your Ground of your power source. Connect the 5v on the LED Ring to a power source of between 3.5v and 5v. (the Arduino can only supply enough power for a few LEDS to be on at a time). Put a 1000uf 10v capacitor between the 5v and GND of the LED Ring to buffer the power at start up. Connect the LED Ring "Data In" to Pin 6 on the Arduino. Put a 470 ohm resister between the Arduino pin 6 and the data line of the LED Ring Change the Arduino code to the number of LEDs on your LED Ring, and make sure the data pin is set to Pin 6. This should now work. The image is from the Adafruit web site (I hope they are ok with me using it)
1pz 8pz 12pz 16pz 24pz WS2812B SMD5050 RGBW RGBWW 4 In 1 Scheda Chip di Luce LED a Forma Rotonda DC5V
US$6.89 US$7.99
10
raccomandazioni
Commento (0)
Stampante 3D T8 Vite a ricircolo di sfere da 300 mm con dado in rame per motore passo-passo con passo da 8 mm 1/2/4/8/12/14 mm
US$10.38 US$10.99

D: it's how long

Domandata da BG521144416 il 2021-04-19 07:11:53

CrispyDuck The clue is in the product title...

2021-04-19 09:02:22 Utile (0)
Consegnare
risposta (2)
CrispyDuck 11/04/2021
Good quality aluminium bracket for the z-axis of a CR-10, but you will need to adjust the distance from the frame to match the z-axis screw rod bearings.
Piastra passiva in alluminio da 2,5 mm per asse Z Creality 3D® per CR-10S Pro Stampante 3D
US$9.23 US$9.99
0
raccomandazioni
Commento (0)
CrispyDuck 11/04/2021
Simple to connect and configure with a Pi. Works well and provides extra volume to sound. The main difference in quality over a standard Pi 2 is a wider range, and clearer sound. It's not immediately obvious, but when you swap between the 2 outputs a few times with a good quality soundtrack you begin to notice the difference. It also provides the extra boost needed to drive an external amplifier. This is where you notice the difference the most.
Decodificatore DAC audio digitale senza perdita con interfaccia I2S IIS PCM5102 GY-PCM5102
US$16.16 US$16.99
0
raccomandazioni
Commento (0)
CrispyDuck 11/04/2021
Good basic power connectors and easy to fit.
10Pz DC-022 Foro Rotondo 5.5-2.1mm Dado Buco Rotondo DC Presa di Corrente ROHS Diametro Interno 5.5mm
US$4.19 US$3.19
0
raccomandazioni
Commento (0)
Motore Mandrino Machifit ER11 CNC 500W con Morsetti da 52mm e Alimentatore di Regolazione della Velocità
US$73.99 US$99.99

D: How do I power up the unit? It is DC right? Difficult to find a DC power converter with 30 Volts

Domandata da flowin_through il 2021-04-07 10:14:27

CrispyDuck The power supply needs to be connected to the mains power. It then provides DC to the motor. Use google for the correct wiring connections. DO NOT TOUCH THE WIRES OR CONNECTORS WHEN PLUGGED IN AS IT IS VERY DANGEROUS. See thingiverse for a 3D printed cover for the power supply connectors to make it safer.

2021-04-07 12:06:27 Utile (0)
Consegnare
risposta (2)
Decodificatore DAC audio digitale senza perdita con interfaccia I2S IIS PCM5102 GY-PCM5102
US$16.16 US$16.99

D: hello can be used with raspberry pi 3

Domandata da newday21 il 2020-06-12 12:54:12

CrispyDuck Yes it can. Info is on the web.

2021-03-25 11:39:26 Utile (0)
Consegnare
risposta (2)
Motore Mandrino Machifit ER11 CNC 500W con Morsetti da 52mm e Alimentatore di Regolazione della Velocità
US$73.99 US$99.99

D: hello! which frame do you suggest for this spindle?

Domandata da BG521345367 il 2020-12-16 12:58:12

CrispyDuck There is a 3D printable bracket for the motor clamp to attach to as well as a better fan on thingiverse.

2020-12-17 05:04:52 Utile (1)
Consegnare
risposta (4)
Adattatore Mandrino Arbor M10 da 5mm/8mm/10mm/12mm per Smerigliatrice Angolare
US$12.64 US$13.99

D: What is the thread length of the M10 one?

Domandata da BG139481445 il 2020-12-02 03:51:33

CrispyDuck The thread is 9mm long with the next bit (thinner shaft without a thread) being 2mm.The next bit (thicker shaft) is 5mm long.The final bit is 26mm long.(I tried to do a text diagram of it, but the crap support system puts it all on 1 line!)

2020-12-02 05:53:28 Utile (0)
Consegnare
risposta (3)
Digoo DG-XME 4 8 12CH 1080P HDMI P2P Autonomo ONVIF 25 NVR Registratore per Sistema di Telecamere IP
US$32.99

D: just ip cam I dig? also other ip cam brands?

Domandata da Gianluca721 il 2018-02-18 06:27:45

CrispyDuck I'veused it with several different IP cam brands. All the ones I tried worked well for me including the bare camera with ethernet cable on BG.

2020-11-28 03:36:07 Utile (0)
Consegnare
risposta (1)
Digoo DG-XME 4 8 12CH 1080P HDMI P2P Autonomo ONVIF 25 NVR Registratore per Sistema di Telecamere IP
US$32.99

D: The hard drive must be formatted in Fat 32 or NTSF?

Domandata da Leniel il 2018-01-14 04:20:03

CrispyDuck Fat32

2020-11-28 03:34:16 Utile (0)
Consegnare
risposta (1)
CrispyDuck 10/09/2020
Camera Screws work as described, and arrived quickly with Banggood Express to the UK. Please note that as the thread nears the head, from halfway in it has been very slightly worn away. Although I initially thought it was a defect with all 3, I now think that it has been done to make it easier to remove something like a nut that has gone too far in. This is a thoughtful bit of design which I like. It fits my mini camera (DSLR) ball heads perfectly, so if I hadn't bought 3 of them I would buy it again.
3 pezzi LS004 BEXIN Vite ad anello a C in acciaio inossidabile da 1/4 di pollice per fotocamera
US$12.69 US$13.99
0
raccomandazioni
Commento (0)
CrispyDuck 10/09/2020
These arrived quickly and work well enough for what I needed, but as all of these type motors are cheaply made you'll have to test the number of turns to make a full 360 deg rotation. All of my motors are different, and they change as they heat up. It's not difficult to work out, but you'll need to do this if you need any kind of accurate movement.
Geekcreit 5Pcs 5V Motore passo-passo con scheda driver ULN2003 Cavo Dupont
US$13.79 US$13.99
0
raccomandazioni
Commento (0)
CrispyDuck 10/09/2020
It works very well and as it has an I2C connector, it is easier to connect than the parallel data ones. The backlight is adjustable so you can make it easy to see the text, and it is easy to program with an Arduino.
Modulo display LCD con retroilluminazione blu Geekcreit® IIC / I2C 1602 Geekcreit per Arduino - prodotti che funzionano con schede Arduino ufficiali
US$6.89 US$9.99
0
raccomandazioni
Commento (0)
CrispyDuck 11/06/2020
A normal basic 3 layer face mask. Better than not having one at all as they do provide some protection, and priced ok. Just remember, do NOT keep on touching them throughout the day as some idiots do. By doing that you transfer any virus on your hands to the mask and then to your face! Please note that these are NOT medical face masks as some other reviews have said. Medical masks have more layers. These are just good basic masks.
20Pcs Disposable Masks Mouth Face Mask 3-layer Dust-Proof Personal Protection
US$3.29 US$11.99
0
raccomandazioni
Commento (0)
CrispyDuck 11/06/2020
Standard 8mm screw threads. Good basic quality.
Stampante 3D T8 Vite a ricircolo di sfere da 300 mm con dado in rame per motore passo-passo con passo da 8 mm 1/2/4/8/12/14 mm
US$10.38 US$10.99
0
raccomandazioni
Commento (0)
CrispyDuck 03/06/2020
It looks decent but unfortunately it arrived bent. As such it is unusable as a replacement for my CR10 lead screw.
Machifit Vite a ricircolo di sfere da 600 mm Vite a ricircolo di sfere da 8 mm Passo di 2 mm Vite a ricircolo di sfere con dado in ottone
US$18.47 US$19.99
0
raccomandazioni
Commento (0)

Sei l'esperto, puoi aiutare?

Ti invitiamo sinceramente a iscriverti all'e-mail di risposta all'invito!

Se ti iscrivi, ti inviteremo via e-mail a rispondere alle domande che le persone hanno sui prodotti. Iscrivendoti] guadagnerai anche il "Badge utile "! Puoi annullare l'iscrizione in qualsiasi momento nella pagina delle impostazioni sulla privacy.

Aiuta gli altri e sii più felice!

  • sottoscrivi

Informazioni sui badge

I badge sono collegati alla community e gli utenti guadagnano badge creando contenuti di qualità, completando missioni o partecipando ad attività speciali. Le persone specifiche avranno anche il proprio badge esclusivo.
Badge CEO

il badge ceo è di proprietà solo del boss di banggood.

I badge che puoi guadagnare arriveranno presto
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe