The OSD doesn't flicker! First one that doesn't, yet. It flies tight but the PID's had to be higher than usual, 75 P and 72 I for pitch. That on a 220 qav only 501 grams. Still though, flies good. I like the connector for esc leads, makes it easy to pull it if u have 2. Clever as all the leads that need to stay on the craft are on the connector, add a JST for the receiver and video in/out and easy out. Came with Betaflight 3.2.1 running 4k gyro and acc loops. This one measured out at 7.2 g. If u solder leads right to the board no pin headers its 4-5 grams lighter than most F3 boards.

The OSD doesn't flicker! First one that doesn't, yet. It flies tight but the PID's had to be higher than usual, 75 P and 72 I for pitch. That on a 220 qav only 501 grams. Still though, flies good. I like the connector for esc leads, makes it easy to pull it if u have 2. Clever as all the leads that need to stay on the craft are on the connector, add a JST for the receiver and video in/out and easy out. Came with Betaflight 3.2.1 running 4k gyro and acc loops. This one measured out at 7.2 g. If u solder leads right to the board no pin headers its 4-5 grams lighter than most F3 boards.

The OSD doesn't flicker! First one that doesn't, yet. It flies tight but the PID's had to be higher than usual, 75 P and 72 I for pitch. That on a 220 qav only 501 grams. Still though, flies good. I like the connector for esc leads, makes it easy to pull it if u have 2. Clever as all the leads that need to stay on the craft are on the connector, add a JST for the receiver and video in/out and easy out. Came with Betaflight 3.2.1 running 4k gyro and acc loops. This one measured out at 7.2 g. If u solder leads right to the board no pin headers its 4-5 grams lighter than most F3 boards.

received this flight controller trying to figure out how to get the osd working, yes its wired in properly but am quite unsure as to weather i have to use the +vbat off the plug to get the data through the osd? Secondly is it possible to put +vbat into this as its description says it only takes up to 5..5v ? Can someone help me with sorting this out or does the osd work but not show any data?... help much appreciated Thanks

received this flight controller trying to figure out how to get the osd working, yes its wired in properly but am quite unsure as to weather i have to use the +vbat off the plug to get the data through the osd? Secondly is it possible to put +vbat into this as its description says it only takes up to 5..5v ? Can someone help me with sorting this out or does the osd work but not show any data?... help much appreciated Thanks

received this flight controller trying to figure out how to get the osd working, yes its wired in properly but am quite unsure as to weather i have to use the +vbat off the plug to get the data through the osd? Secondly is it possible to put +vbat into this as its description says it only takes up to 5..5v ? Can someone help me with sorting this out or does the osd work but not show any data?... help much appreciated Thanks

Very good and stable FC with OSD and Sd card functions. Sbus works on rx6. Must soft mount it to reduce vibrations,

Very good and stable FC with OSD and Sd card functions. Sbus works on rx6. Must soft mount it to reduce vibrations,

Very good and stable FC with OSD and Sd card functions. Sbus works on rx6. Must soft mount it to reduce vibrations,

from mumbai,india. I got v2 delivered I dont know why.. but its looking nice I will be updating soon

from mumbai,india. I got v2 delivered I dont know why.. but its looking nice I will be updating soon

from mumbai,india. I got v2 delivered I dont know why.. but its looking nice I will be updating soon

FC works great I will buy another wiring was easy straight forward j like it so far

FC works great I will buy another wiring was easy straight forward j like it so far

FC works great I will buy another wiring was easy straight forward j like it so far

Sta funzionando

работает

Sta funzionando

The plasticity of this board is great. you can solder each of your motor ESC signal wires to individual pads or use a single ribbon cable. I opted to use the single ribbon cable approach with my signal wires vbat and current sensor all in one place. The motor signals worked great however vbat and current values do not work as they do not show up on osd.

The plasticity of this board is great. you can solder each of your motor ESC signal wires to individual pads or use a single ribbon cable. I opted to use the single ribbon cable approach with my signal wires vbat and current sensor all in one place. The motor signals worked great however vbat and current values do not work as they do not show up on osd.

The plasticity of this board is great. you can solder each of your motor ESC signal wires to individual pads or use a single ribbon cable. I opted to use the single ribbon cable approach with my signal wires vbat and current sensor all in one place. The motor signals worked great however vbat and current values do not work as they do not show up on osd.

This clone works like the original. No issues. Has survived MultiGP race crashing.

This clone works like the original. No issues. Has survived MultiGP race crashing.

This clone works like the original. No issues. Has survived MultiGP race crashing.

ottimo

ottimo

ottimo

Awesome flight controller! Work with all the sensors i need. GPS, compass etc. Very stable and responsive! The image is if my 3D printen fpv drone.

Awesome flight controller! Work with all the sensors i need. GPS, compass etc. Very stable and responsive! The image is if my 3D printen fpv drone.

Awesome flight controller! Work with all the sensors i need. GPS, compass etc. Very stable and responsive! The image is if my 3D printen fpv drone.