Its good module. I use it for DIY Headtracker building . This pretty piece and GY-85 .

Its good module. I use it for DIY Headtracker building . This pretty piece and GY-85 .

Its good module. I use it for DIY Headtracker building . This pretty piece and GY-85 .

Very good card, good quality Very small 33mmx18mm, for all DIY projects

Very good card, good quality Very small 33mmx18mm, for all DIY projects

Very good card, good quality Very small 33mmx18mm, for all DIY projects

I bought 3 of these Pro mini 328 5V 16Mhz and I spent a day trying to load sketches to no avail. I reloaded a bootloader on all boards, still no luck, sketches would not load. I tried several USB adapters, IDE 1.0.3 and 1.6.2 In despair, I tried to load a sketch choosing "Nano w/ ATmega328" instead of "Pro mini" and, bingo, it loaded fine ! Same for the other 2 Pro mini : they work as "Nano w/ ATmega328". In the end I'm happy they all work fine but I've lost a day on this nonsense.

I bought 3 of these Pro mini 328 5V 16Mhz and I spent a day trying to load sketches to no avail. I reloaded a bootloader on all boards, still no luck, sketches would not load. I tried several USB adapters, IDE 1.0.3 and 1.6.2 In despair, I tried to load a sketch choosing "Nano w/ ATmega328" instead of "Pro mini" and, bingo, it loaded fine ! Same for the other 2 Pro mini : they work as "Nano w/ ATmega328". In the end I'm happy they all work fine but I've lost a day on this nonsense.

I bought 3 of these Pro mini 328 5V 16Mhz and I spent a day trying to load sketches to no avail. I reloaded a bootloader on all boards, still no luck, sketches would not load. I tried several USB adapters, IDE 1.0.3 and 1.6.2 In despair, I tried to load a sketch choosing "Nano w/ ATmega328" instead of "Pro mini" and, bingo, it loaded fine ! Same for the other 2 Pro mini : they work as "Nano w/ ATmega328". In the end I'm happy they all work fine but I've lost a day on this nonsense.

The heading is misleading. This is not a Nano clone, but a "PRO MINI" clone. It does say so in the fine print, but that heading could make you expect a Nano as I did. Nothing wrong with the product though, just make sure that you know what you are getting or you will be disappointed.

The heading is misleading. This is not a Nano clone, but a "PRO MINI" clone. It does say so in the fine print, but that heading could make you expect a Nano as I did. Nothing wrong with the product though, just make sure that you know what you are getting or you will be disappointed.

The heading is misleading. This is not a Nano clone, but a "PRO MINI" clone. It does say so in the fine print, but that heading could make you expect a Nano as I did. Nothing wrong with the product though, just make sure that you know what you are getting or you will be disappointed.

It's perfect for anytime you need miniaturization

It's perfect for anytime you need miniaturization

It's perfect for anytime you need miniaturization

very fast shipping. i love it

very fast shipping. i love it

very fast shipping. i love it

tested one and works well. was able to flash through UNO. fast shipping too. pic is how I connected to UNO board. Tx to Tx, Rx to Rx, 5v and ground. also need to ground the reset pin on UNO board to disable the boot loader. when flashing wait for the message to change to 'uploading ' and then press the reset button on the pro-mini. if u time it correctly then your program will be uploaded successfully.

tested one and works well. was able to flash through UNO. fast shipping too. pic is how I connected to UNO board. Tx to Tx, Rx to Rx, 5v and ground. also need to ground the reset pin on UNO board to disable the boot loader. when flashing wait for the message to change to 'uploading ' and then press the reset button on the pro-mini. if u time it correctly then your program will be uploaded successfully.

tested one and works well. was able to flash through UNO. fast shipping too. pic is how I connected to UNO board. Tx to Tx, Rx to Rx, 5v and ground. also need to ground the reset pin on UNO board to disable the boot loader. when flashing wait for the message to change to 'uploading ' and then press the reset button on the pro-mini. if u time it correctly then your program will be uploaded successfully.

I found a site that showed me how to modify my RC832 Receiver using this Arduino Pro Mini board and the HC-06 Bluetooth module. It allows me to use an App on my phone to change the frequency and auto scan. It took about an hour mostly because the board was setup differently than the one used in the demo and wanted to make sure I had the correct connections. The A6 & A7 pins are in different locations and I was looking for the VCC on the side of the board (there is one on the end of the board) but this says ACC. I was not familiar with ACC but took a chance and it worked. The board was easy to flash and had no issues.

I found a site that showed me how to modify my RC832 Receiver using this Arduino Pro Mini board and the HC-06 Bluetooth module. It allows me to use an App on my phone to change the frequency and auto scan. It took about an hour mostly because the board was setup differently than the one used in the demo and wanted to make sure I had the correct connections. The A6 & A7 pins are in different locations and I was looking for the VCC on the side of the board (there is one on the end of the board) but this says ACC. I was not familiar with ACC but took a chance and it worked. The board was easy to flash and had no issues.

I found a site that showed me how to modify my RC832 Receiver using this Arduino Pro Mini board and the HC-06 Bluetooth module. It allows me to use an App on my phone to change the frequency and auto scan. It took about an hour mostly because the board was setup differently than the one used in the demo and wanted to make sure I had the correct connections. The A6 & A7 pins are in different locations and I was looking for the VCC on the side of the board (there is one on the end of the board) but this says ACC. I was not familiar with ACC but took a chance and it worked. The board was easy to flash and had no issues.

Arduino pro miniera topp più

Arduino pro mine topp de mais

Arduino pro miniera topp più

Articolo come descritto. Arrivato in 2 mesi (consegna in Italia). Effettuato solo un test di potenza e sembrava essere ok.

Item as described. Arrived in 2 months (delivery to Italy). Performed just a power test and seemed to be ok.

Articolo come descritto. Arrivato in 2 mesi (consegna in Italia). Effettuato solo un test di potenza e sembrava essere ok.