Recensioni clienti

4.75 su 5
Scrivi una recensione
  • Tutte le recensioni (48)
  • Immagine (1)
  • Video (0)
  • Tutte le stelle
    • Tutte le stelle(48)
    • 5 Inizia(43)
    • 4 Inizia(2)
    • 3 Inizia(0)
    • 2 Inizia(2)
    • 1 Inizia(1)
Ordina per:
Recensione Top
  • Recensione Top
  • Il più utile
  • Più Recente
Recensioni solo dal tuo paese (Italy)
  • May-29 2017 11:59:00

    Good quality, as you can see i fitted 1.75mm Black Filament very good traction.

    Commento
  • June-17 2020 18:38:28

    Unlike ordered elsewhere, the FILAMENT holes are finished through and not crooked. Suggest you order this item on BANGGOD.com.

    Commento
  • October-30 2020 05:40:11

    ottimo e conforme

    Commento
  • April-25 2020 10:29:44

    RAS. Produit conforme

    Commento
  • November-25 2017 05:25:22

    This Coldend has a very good qualitiy but a few small designflaws. For changeing the filament, you need a high force to press the lever down. this is good, because the fiament is pushed firmly to the drivewheel. But this high force can bend the linear rods from the printer. There would be an counterlever helpfull to reduce the risk of damaging the printer. And a other problem is, you need to disassamble the product for instaling. But because you instal it only once, it is no big deal. Overall it

    Commento
  • November-07 2017 14:55:31

    The "screw" pushing filament has smaller teeth than original anet and doesn't damage the filament. I would recommend this for bowden if it had adapters for bowden (It doesn't have those). One of the screws is triangle head very small so if you are planning to use this as bowden keep in mind that you will need to buy longer triangle heat screw.

    Commento
  • October-20 2017 04:07:48

    Using this on my MeCreator 2, it has been performing better and more reliable than the original. Now I was going to use my FlexPLA filament, and ran into issues. Seems the filament can squeeze itself out thru gaps, and curl up inside the extruder. So I can't print very much even at slow speeds. Trying to figure out a new solution.

    Commento
  • August-29 2017 13:35:46

    I bought one to replace my Malyan M150 (Wanhao i3 clone) MK10 one that was broken. It's a couple of mm thicker than the one I have so it's not a ready to install replacement but after adding a little spacer between the aluminium block and the extruder motor it fit well. Used for two month till now anf works great.

    Commento
  • January-19 2019 06:15:54

    le produit est conforme au descriptif mais il est difficile de choisir entre le gauche et le droite et bien évidemment je n'est pas pris le bon ! il serais bien d'avoir la photo de la pièce pour le choix !

    Commento
  • April-06 2018 03:29:23

    works well and even though it looks cheap it is actually quiet and strong. Do remember that you will need some block for mounting bowden tube or mounting to direct drive.

    Commento
Show:

    Total 0 pages

    Go to page

    Go

    Magari ti piace

    recommendation for you
    • 7,79€
    • 4,19€
    • 7,31€
    • 7,42€
    • 2,11€
    • 14,73€
    • 16,02€
    • 11,13€
    • 3,09€
    • 1,97€
    • 11,26€
    • 12,10€
    • 32,19€
    • 1,16€
    • 73,38€
    • 3,45€
    • 24,76€
    • 1,20€