Recensioni Contatore di energia digitale DC multifunzione da 100A modulo monitor voltmetro amperometro 6.5V-100 - Banggood Shopping online Italia

:

Download the

Banggood App

Scarica l'app per ottenere

3 dollari USA buono sconto

Spedire a:

Lingua:

Valuta:

Ciao Accedi Partecipare
Accedi Unisciti a noi
Nuovo cliente? Comincia qui.
0

Contatore di energia digitale DC multifunzione da 100A modulo monitor voltmetro amperometro 6.5V-100

US$29.99
~~US$35.99~~
Acquista ora

Recensioni clienti

4.82 su 5

Vedi tutte 68 recensioni

Scrivi una recensione Ottieni punti doppi di Banggood se sei uno tra i primi 3 clienti ad aver pubblicato una recensione del prodotto.

Tutte le recensioni (68)
Immagine (4)
Video (0)
Tutte le stelle
- Tutte le stelle(68)
- 5 Inizia(62)
- 4 Inizia(2)
- 3 Inizia(3)
- 2 Inizia(0)
- 1 Inizia(1)

Ordina per:

Recensione Top

Recensione Top
Il più utile
Più Recente

Recensioni solo dal tuo paese (Italy)

|

Spettacolo originale

Una parte della recensione è stata tradotta automaticamente.

Rory FlorenceVIP1
11/11/2015

To get more accurate readings or if your display is flashing... The problem is the length of wires from where the shunt is (if it is not right next to the battery) causes a voltage drop across the cable that influences the reading and in most causes will cause the meter to flash as I suspect this is the over-read indication. (I am using three meters to measure two banks of solar panels and a wind generator) Solution: tie the battery side of the shunt wire to both 0v points on the meter . i.e. bridge the two inner pins of the connector and take the wire only to the shunt, this then takes the voltage drop over the cable to the battery out of the equation.

To get more accurate readings or if your display is flashing... The problem is the length of wires from where the shunt is (if it is not right next to the battery) causes a voltage drop across the cable that influences the reading and in most causes will cause the meter to flash as I suspect this is the over-read indication. (I am using three meters to measure two banks of solar panels and a wind generator) Solution: tie the battery side of the shunt wire to both 0v points on the meter . i.e. bridge the two inner pins of the connector and take the wire only to the shunt, this then takes the voltage drop over the cable to the battery out of the equation.

To get more accurate readings or if your display is flashing... The problem is the length of wires from where the shunt is (if it is not right next to the battery) causes a voltage drop across the cable that influences the reading and in most causes will cause the meter to flash as I suspect this is the over-read indication. (I am using three meters to measure two banks of solar panels and a wind generator) Solution: tie the battery side of the shunt wire to both 0v points on the meter . i.e. bridge the two inner pins of the connector and take the wire only to the shunt, this then takes the voltage drop over the cable to the battery out of the equation.
9

Commento

Spettacolo originale
Ravi bhatVIP2
IN
02/08/2018

good product price is too high for its function.working fine for me"wh"is not useful

good product price is too high for its function.working fine for me"wh"is not useful

good product price is too high for its function.working fine for me"wh"is not useful
0

Commento

Spettacolo originale

Show:

Totale 0 pagine

Vai alla pagina

Partire

Magari ti piace

recommendation for you